How to Make a Sliceform Sphere Lantern (Step by Step)
A sliceform sphere is a paper globe made from flat curved strips that slot into each other at right angles - no glue holds the shell together. Half the strips run one way (the A pieces), half run the other (the B pieces), and once they are all locked in, the grid curves into a sphere with a scene glowing in the centre. It looks complicated, but it follows one rule: start with the two centre strips, then work outwards in numbered pairs. This guide shows how, using our Pack 4 Deer Sphere.

What a Sliceform Sphere Is
The technique is older than it looks. In Munich around 1870, the mathematicians Alexander von Brill and Felix Klein used slotted card to build models of mathematical surfaces for teaching, and the name "sliceform" was later coined by the writer John Sharp. Paper engineers also call it a lattice-style pop-up: two sets of parallel paper pieces slotted together.
Here is how it works: each strip has slots cut halfway across it, and two strips cross by sliding slot into slot. On a sphere, the strips are arcs of different lengths. Short arcs near the edge, long arcs through the middle. When every A strip crosses every B strip it meets, the grid holds itself in a rounded shape without any glue.
| Compared with | Sliceform sphere |
|---|---|
| A paper lantern | No glue tabs on the shell; light comes through a lattice instead of cut-outs |
| A pop-up card | Free-standing and much larger, about 20-24 cm |
| A shadow box | Seen from every side, not just the front |
What You Need
- Paper, 220-300 gsm. Watercolour paper at 250-300 gsm gives the best light effect. A 20 cm sphere uses about 26 A4 or US Letter sheets.
- A cutting machine. The slots must be exact, so a Cricut, Silhouette or ScanNCut is strongly recommended over hand-cutting.
- A pencil or fine pen to make the piece numbers easy to see.
- An LED light base - a round wooden LED display base is ideal.
- The assembly diagram from your download, printed at full size.
Step 1: Cut and Mark the Pieces
Cut all the strips, then sort them into two piles: A pieces (1A to 15A on the Deer Sphere) and B pieces (1B to 15B). Then:
- Find the centre mark on each strip. The centre mark of every A piece sits on axis 1B, and the centre mark of every B piece sits on axis 1A.
- Make the numbers visible. Each strip has its number cut or etched lightly; go over it in pencil. The number also marks the front of the strip, which matters later.
- Colour-code 1A and 1B. A pencil line along the two longest strips makes the main axes easy to find while you work.
If the cut is ragged around the slots, check Cricut not cutting through cardstock before you cut the rest - heavy watercolour paper usually needs a deeper or slower setting.
Step 2: Lock the Two Main Axes
Lay the printed diagram on the table. Take 1A and 1B, line their centre marks up over the centre of the diagram, and slide them together slot into slot so they form an X. These two strips are the spine of the sphere; every other strip is placed relative to them.
Every strip must follow its line on the diagram, with its printed number facing you. A strip turned back to front will not meet its partners at the right slots.
Step 3: Add the Pairs in Order
Work outwards in pairs, always an A then its matching B:
- 2A, then 2B
- 3A, then 3B
- Continue to 8A and 8B on one side
- Then 9A and 9B, 10A and 10B, through to 15A and 15B on the other side
Hold the growing sphere over the diagram as you go and check each strip against its line. The outer strips are shorter and stiffer to slot in; if one fights you, bend it gently along its length first. Never force a slot - a torn slot is the one mistake you cannot hide.

Step 4: Fit the Inner Scene
The scene in the middle - deer, a golfer, dragonflies - is built from inner pieces labelled AB. Slide them into the lattice in the order on the diagram. On the Deer Sphere that is 4AB, 3AB, 2AB, 1AB, then 9AB and 10AB. Once they are in, the inner layers are easy to recognise from the front.
The Deer Sphere includes four scenes - Deer, Couple Deer, Deer Family and Deer with Snowman - that all fit the same shell, so once you have built one, the next goes together much faster.
Step 5: Light and Display It
- Stand the sphere on a round LED light base so the light rises through the lattice.
- Warm white suits woodland, golf and pet scenes; a cooler white suits a winter deer.
- Keep it away from candles and radiators - the shell is open paper.
Sliceform spheres, ready to cut
Deer, golfer, dragonfly, pet and Easter designs - SVG and PDF cut files, instant download.
Shop pop-up SVG filesTroubleshooting
| Problem | Cause | Fix |
|---|---|---|
| Strips will not meet at the slots | A strip is back to front | Turn it so the number faces you |
| The sphere is lopsided | Centre marks not on the axes | Re-seat 1A and 1B on the diagram centre, then re-check each pair |
| Outer strips tear | Paper too thick or slot forced | Bend the strip first; use 250 gsm rather than 300 gsm |
| Slots too tight | Blade not cutting cleanly | Replace the blade; clean the slot with a craft knife |
| Scene leans | Inner AB pieces in the wrong order | Remove them and refit in the diagram order |
Sliceform Designs
The Dog and Cat Moon and the Easter eggs use the same slotting method with a different outline: a crescent and an egg rather than a sphere. For the Easter designs in context, see Easter 2027 paper lantern and shadow box ideas.
Frequently Asked Questions
Do you need glue for a sliceform sphere?
No. The strips hold each other by their slots, so the shell needs no glue at all.
What paper is best for a sliceform sphere?
Watercolour paper at 250-300 gsm gives the best light effect. Anything under 220 gsm is too soft to hold the curve.
How many sheets does a sphere take?
About 26 A4 or US Letter sheets for a 20 cm sphere, about 28 for the Dog and Cat Moon, and 19 for each Easter egg.
Where do I start assembling?
With the two longest strips, 1A and 1B, crossed at their centre marks over the printed diagram. Then add 2A and 2B, 3A and 3B, and so on outwards.
Can I cut a sliceform by hand?
It is possible from the PDF, but the slots must be exact for the sphere to close evenly, so a cutting machine is strongly recommended.